Plumbing 101: What You Must Have for Bathtub Installation
Plumbing 101: What You Must Have for Bathtub Installation
Blog Article
Listed here below you can discover lots of quality ideas involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably difficult project. If the old tub is conveniently easily accessible, the job can move immediately; if you need to open up a wall surface to eliminate the old tub and place the brand-new bath tub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to vacate the old tub and also set in the new one. Make sure you have certified on your own for the work and also are comfortable trying it. Rather than employing a specialist to take over a halfway-completed job, it is better to think about using one before you start. Possibilities are you might need a specialist plumber to make tube links.
This short article will certainly help you install a new bath tub in your restroom if you have currently gotten a brand-new tub and also do not require to alter the setup of your previous water supply pipes.
Your tools and also product checklist ought to comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly troublesome because of the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before moving on to fit the new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Protect the tap in place with the maker offered backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The previous kind should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Making use of the two wood boards under its feet, place the bath tub in the required setting. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the tub until the spirit level reads degree.
To install taps, fit all-time low of the furthest flexible tap port to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Turn on the water system and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Load the bathtub as well as also examine the overflow outlet and the typical outlet for leakages.
Ultimately, deal with the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the tub needs to wait till the bath tub has been used at least when as this will resolve it right into its final position.
Preparing for the Installment
Firstly, the sustaining frame supplied with the bath should be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to stop pressure on the tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break a rigid seal, creating the water to pass through the wall surface in between the bath and also the tiling, causing difficulties with moisture and possible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealant can break relatively early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that excerpt was a good thing. If you please set aside a second to promote this blog posting if you appreciated it. Thank you for going through it.
24/7 plumbers for emergencies. Report this page